• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
ASSEMBLE  THRUST  CCD ACTUATOR (AVIM) (Continued) - TM-55-1520-240-23-9_659
ASSEMBLE  THRUST CCD ACTUATOR  (AVIM) (Continued) - TM-55-1520-240-23-9_661

TM-55-1520-240-23-9 CH-47D Heilcopter Manual
Page Navigation
  633    634    635    636    637  638  639    640    641    642    643  
TM  55-1520-240-23-9 11-157 ASSEMBLE  THRUST CCD ACTUATOR  (AVIM) (Continued) 11-157 Hydraulic fluid  (E199)  is toxic.  It  can irritate  skin  and  cause  burns.   Avoid inhaling.   Use  only  with  adequate ventilation.  Avoid  contact  with  skin, eyes,  or  clothing.  In  case  of  contact, immediately  flush  skin  or  eyes  with water  for  at  least  15 minutes.   Get medical  attention  for  eyes. 24. Soak four  new  disks (49)  in  hydraulic fluid  (E199) for  one  hour  before  installing.   Wear  gloves (E184.1). 25. Install  shims  (50),  spacers  (51),  plate  (52), new disk  (49),  arm  (53), two  new  disks (49),  and  two plates  (54)  on  shaft  (55). 26. Install  bearing  (56)  in  arm  (57).  Use  arbor  press. Epoxy  primer  (E292)  is  flammable and  toxic.   It  can  irritate  skin  and use  burns.  Use  only  with  adequate ventilation, away  from  heat or  open flame.   Avoid  contact  with  skin,  eyes, or  clothing.    In  case  of  contact, immediately  flush  skin  or  eyes  with water  for  at  least  15 minutes.   Get medical  attention  for  eyes. 27. Apply  coat  of  epoxy  primer  (E292)  on  washer (58).  Install  washer  wet  on  pin  (59).  Use  gloves (E184.1). 28. Install  pin  (59),  washer  (60),  nut  (61), and  cotter pin  (62)  in  arm  (57). 29. Install  arm  (57)  on  shaft  (55).  Align  pin  (59)  and slot  (63)  in  arm  (53). 30. Install  new  disk (49)  and  plate  (64)  on  shaft  (55). 31. Press  plate  (64)  toward  chassis  (13).   Check outer  surface  of  plate  is  0.020 to 0.025  inch outward  of  shoulders  (65)  on  shaft  (55).   Use feeler  gage  and  scale.  If  gap  is  greater,  remove shims  (50).   If  gap  is  smaller,  add  shim  (50). There  must be  a  minimum  of one  shim  between spacer  (51)  and  chassis  (13). 32. Install  three  spring  washers (66),  shims (67), and nut (68).  Torque  nut  to  27  inch-pounds. 33. Perform  torque  test  (Task  11-279). 34. Align  slot  (69)  of plate  (64)  and  hole  (70)  of  nut (68). 35. Install  spacer  (71)  and  rivet  (72)  in  hole  (70). Use  0.312  inch  outside  diameter  drill  bushing in  slot  (69). 11-644







Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.